Make the 09 PLANTS layer active

Load the 09-plants selection and fill with the same green #5C7C5C and deselect.

Apply the same cutout you used for the other plants.

Make the 10 SAND layer active

Load the 10-sand selection and fill with the same as the other sand #795B47 and deselect.

Apply the same steps as before to add noise here too.

Make the 11 GLASS your active layer

Load the 11-glass selection and fill this with black about 3 or 4 times and deselect.

Make the 12 HIGHLIGHTS layer active

Load the 12-highlights selection and fill with white. Deselect and turn the opacity of this layer down to about 35.

Make the 13 TOP BOTTOM layer active

Load the 13-top-bottom selection and fill with black about 3 or 4 times and deselect.

Make the 14 HEAD layer active

Load the 14-head selection and fill with black and deselect.

Use a cutout with these settings...

Vertical = 0
Horizontal = 0
Opacity = 80
Blur = 20
Shadow color = White
Fill interior with color = Black

Add a new raster layer right above the head, Make an ellipse selection like the one shown below and airbrush some white here the same way you did the body.

Another ellipse and more white with the airbrush...

And again...

And again...

Then you can load the 14-head selection again and go to "selections" "invert" and then "edit" "clear" to clean up anything going outside the head.

Make the 15 HEAD layer active

Load the 15-head selection and fill with white, deselect.

Use a cutout with these settings...

Vertical = 0
Horizontal = 0
Opacity = 80
Blur = 20
Shadow color = Black
Fill interior with color = White

And use the smudge brush to pull the edges out here, the same way you did the feet...

Add a new raster layer here and use the selection tool to make an ellipse on one side, then hold down the Shift key and make another ellipse selection on the other side...

Then go to "selection" "invert"

Use the airbrush (size about 10) and black for the color to shade the bottom of the two ellipses for a little mouth and deselect.

Make the 16 HEAD PAWS your active layer

Load the 16-head-paws selection and fill with white, deselect.

Use the same cutout here, changing the Blur to 15 and leaving the other settings the same.

Smudge the edges out here too...

Add a new raster layer here and again, use the selection tool to make an ellipse and use the airbrush again with black to make some lines for both the paws...

Make the 17 NOSE layer active

Load the 17-nose selection and fill with pink #CB8787 and deselect.

Use Lighten and Darken RGB to darken around the edges and lighten in the middle... I think an inner bevel might work here too...

Make the 18 EYES layer active

Load the 18-eyes selection and fill with blue #636E82 and deselect.

Again use Darken RGB to shade around the outside.

Still on this layer use a drop shadow with these settings.

Vertical = 0
Horizontal = 0
Opacity = 80
Blur = 15
Color = White

Make the 19 EYES layer active.

Load the 19-eyes selection and fill with black, deselect.

Add a new raster layer here and use the airbrush, color white, airbrush size about 6 and make two small white highlights in the eyes.

Add a new raster layer and use the airbrush to paint two white lines above the eyes

And use the smudge brush to smudge it upwards, you may need to play with the settings to get the look you want.

And do the same thing for a little white fur inside the ears

I added some little whiskers on the cheeks and under the ears, using single line, white, and used an eyecandy jiggle on the whiskers...

Here's the finished kitty :o)